View MAX1617AEVKIT_313156.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

19-2505; Rev 1; 9/02
MAX1617A Temperature Sensor Evaluation Kit
General Description
The MAX1617A evaluation kit (EV kit) is a demonstration platform for the MAX1617A temperature-sensor IC. It monitors both the junction temperature of the IC and the temperature of a remote (external) diode-connected transistor, and converts these temperatures to 8-bit, 2-wire serial data. A 2N3904 remote temperature-sensor transistor comes soldered to the board in a SOT23 package, but for more realistic experiments, it can easily be removed and connected through a twisted pair to the DXP and DXN terminals. The EV kit is designed to be connected to a standard IBM-compatible PC parallel printer port. Signals from the parallel port are converted to open-drain SMBusTM clock and data by a 74HC05 logic chip on the board. An onboard MAX1615 linear regulator steps down the unregulated DC input to 5V to power the glue logic, the MAX1617A, and the SMBus pullup resistors. The software runs under WindowsTM 95, 98, or 2000. This user-friendly program is menu-driven and offers a graphic user interface with control buttons and numeric data displays. Note: Windows 2000 requires the installation of a driver; refer to Win2000.pdf or Win2000.txt located on the diskette.
____________________________Features
o Measures and Displays Sensor Temperature o Simultaneously Monitors Package and a Remote Sensor o Programs Alarms, Configuration, and Rate o Operating Temperature Ranges -55C to +125C (remote sensor) 0C to +70C (board) o Easy to Use o Includes: Windows 95/98/2000 Software, Demo PC Board, 3.5 in. Floppy Disk
Evaluates: MAX1617 A
Ordering Information
PART MAX1617AEVKIT TEMP RANGE 0C to +70C IC PACKAGE 16 QSOP
Component List
DESIGNATION C1, C11, C13 C2 C12 J1 JU1, JU2 Q1 R1 R1 R2 R11, R12 R13, R14, R15 SW1 U1 U11 U12 QTY 3 1 1 1 2 1 1 1 1 2 3 1 1 1 1 DESCRIPTION 0.1F, X7R ceramic capacitors 2200pF, X7R ceramic capacitor 4.7F, 10V tantalum capacitor DB25 male right-angle connector 3-pin headers NPN transistor On Semiconductor MMBT3904 6-pin SIP socket strip 10k, 6-pin SIP resistor pack 200, 5% resistor 4.7k, 5% resistors 47k, 5% resistors Slide switch, 0,150" pitch MAX1617AMEE MAX1615EUK SOT top mark = ABZD 74HCT05 open-drain hex inverter
Quick Start
* A computer running Windows 95, 98, or 2000 (Note: Windows 2000 requires the installation of a driver; refer to Win2000.pdf or Win2000.txt located on the diskette.)
Recommended Equipment
* Parallel printer cable, straight-through 25-pin maleto-female type * DC power supply, 9V at 50mA
Procedure
The MAX1617A EV kit is fully assembled and tested. Follow the steps below to verify board operation. Do not turn on the power supply until all connections are completed: 1) Set up the hardware. Connect the parallel cable to the computer port and to the EV kit board (or else simply plug the board directly into the port without the cable). The parallel port is typically labeled LPT or PRINTER. Adjust the power supply to 9VDC and connect it to the POS9 and ground terminals on the EV kit. Do not apply voltages higher than 28V.
Windows is a trademark of Microsoft Corp. SMBus is a trademark of Intel Corp. ________________________________________________________________ Maxim Integrated Products 1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800. For small orders, phone 1-800-835-8769.
MAX1617A Temperature Sensor Evaluation Kit Evaluates: MAX1617 A
2) Install the software. The MAX1617A.EXE software can be run from the floppy or from a hard drive. Simply use the Windows program manager to run the program. Another autodetect routine attempts to find the MAX1617A by cycling through the nine possible addresses. After the parallel port and address are set up, the userinterface panel appears. The MAX1617A is now operating in its default power-on-reset (POR) mode, auto-converting at a 0.25Hz rate. The display shows the current temperature for both remote and local channels. Note that in places where the slave address asks for an 8-bit value, it must be the 7-bit slave address of the MAX1617A as determined by ADD0 and ADD1 with the last LSB bit always set to one.
Data Logging
Data logging commands are accessed via the pulldown menu labeled "MAX1617A". Data logging saves temperature data for both channels to a text file that includes a time/date stamp next to each data point. At high conversion rates, not every data point is logged, depending on the speed of the disk drive where the file is being written. To stop data logging, select Logging from the pull-down menu.
Detailed Description
User-Interface Panel
The user interface is easy to operate; use the mouse, or press the Tab key to navigate with the arrow keys. Each of the buttons corresponds to bits in the command, conversion-rate, and configuration bytes. Clicking on them generates the correct SMBus write operation to update the internal registers. The program continually polls the device for new temperature data and status, and alerts at a rate faster than the fastest conversion rate. To change the THIGH and TLOW alarm-threshold comparison registers, select the appropriate data field and type in the new value. Pressing Enter after typing in the new values updates the internal registers. To make single-shot conversions, click the Stop button under Configuration, and then click on the Measure Now button. Single-shot conversions can also be performed while the device is auto-converting. The singleshot command overrides the automatic conversion. After the single shot is complete, the device returns to automatic operation. If an interrupt condition is generated, typically by the temperature crossing one of the alarm threshold levels, a message appears in the alert box: "ALERT! INT = LOW". To clear the interrupt, first eliminate the condition that caused it (typically by resetting the alarm threshold) and then click on Read Alert. This action reads the Alert Response address, returns the value of the current MAX1617A slave address, and clears the interrupt.
Jumper and Switch Settings
Two jumpers set the MAX1617A slave address. The default address is 0101 010 (ADD0 = ADD1 = high-Z); to get other settings, jumper JU1 and/or JU2 must be installed (Figure 1). JU1 responds to ADD0 and JU2 corresponds to ADD1; see Table 8 in the MAX1617A data sheet for a complete list of slave addresses. The MAX1617A must undergo a power-on reset for the new address to become effective. A slide switch, SW1, is provided as a means to force a power-on reset of the MAX1617A. This switch simply disables power to the device. The STBY hardware standby control input is hard-wired to VCC. In order to apply an external disabling signal to STBY, the narrow PC board trace at JU3 must first be cut. Figure 2 is a component placement guide. Figures 3 and 4 are the PC board layout.
Operating Temperature Range
The operating temperature range of this kit is 0C to +70C, although the MAX1617A itself is rated for -55C to +125C. The limitation is due to the maximum ratings of other components on the board, such as the connector and the logic chips. Specifications aside, the board can tolerate -55C to +125C temperatures. To facilitate testing the MAX1617A in a temperature chamber, cut the PC board along the dotted line and attach wires between the five terminals along the break. Thus, the MAX1617A can be heated or cooled without the parallel cable or interface in the chamber.
Simple SMBus Commands
There are two methods for communicating with the MAX1617A: via the normal user-interface panel, or via the simple SMBus commands available from the SMBus pulldown menu. To stop normal user-interface execution so that it does not override the manually set values, turn off the update timer that slaves the program to the conversion rate by clicking the Automatically Update Displays button.
2
_______________________________________________________________________________________
MAX1617A Temperature Sensor Evaluation Kit Evaluates: MAX1617 A
Table 1. Troubleshooting Guide
SYMPTOM POSSIBLE PROBLEM Bad connections No SMBus Hardware Detected message Power supply Question marks displayed in status and temperature data fields SMB Clock Stuck Low or SMB Data Stuck Low message Both channels always read 0C, or new limits are not accepted, or ALERT interrupts are not seen by the program. The supply voltage at VCC is too low (<4.5V) but is higher than 1V. Remote diode always reads 0C. Remote diode always reads +127C. Remote diode reads a value that is too high. DXP and DXN are shorted together, or DXP is shorted to GND DXP open Excess resistance Excess capacitance Poor-quality diode Check remote diode connections. Check remote diode connections. Check resistance in diode path. Check capacitance from DXP to DXN. Use a good-quality, diode-connected, small-signal No MAX1617A connected Short circuit SOLUTION Check the parallel cable. If it is a straight-through type, try a different cable or connect directly to the port with no cable. Check the supply voltage setting for correct polarity. Use a DMM to check the voltage directly at the board. Check the connections to the device. The SMBus interface is working, but the MAX1617A is not. Check the position of the slide switch. Use a DMM to monitor the SMBCLK and SMBDATA terminals. They may be accidentally shorted.
Bad power supply
Check the 9V supply. The board may be parasitically deriving power from the parallel-port logic signals.
Component Suppliers
SUPPLIER On Semiconductor Sprague PHONE 602-244-6600 402-563-6866 FAX 602-244-4545 402-563-6296 WEBSITE www.onsemi.com www.vishay.com
_______________________________________________________________________________________
3
MAX1617A Temperature Sensor Evaluation Kit Evaluates: MAX1617 A
POS9 9V
6V < VIN < 28V
1 IN C13 0.1F
5 SHDN
U11 3 4 C12 4.7F PO55 VCC5 5V
OUT MAX1615 5/3
J1-5
LOOPBACK
GND 2
J1-13 5V GND R13 47k 8 14 GND1 9 CLK1 SMBCLK_OUT J1-2 11 10 JU3 R11 4.7k 15 R15 47k SMBDATA_IN J1-11 R14 47k 6 5 DATA1 SMBDATA_OUT J1-3 R12 4.7k SMBALERT J1-10 J1-18 J1-19 J1-20 J1-21 J1-22 J1-23 J1-24 J1-25 3 7 4 U12 74HC05 ALERT1 ALERT2 ADD0 10 ADD1 6 11 7, 8 ALERT MAX1617A DXN GND 4 DATA2 STBY 14 12 SMBCLK SMBDATA DXP 3 C2 2200pF 2 VCC DXP1 Q1 MMBT3904LT1 C1 0.1F CLK2 10k EACH R1 (SIP) GND2 R2 200 STBY1 VCC_SW C11 0.1F POR SW1
SMBCLK_IN J1-12
5V J1-15
DXN1
3 DETACH HERE 2 JU2 1
3 2 JU1 1
Figure 1. MAX1617A EV Kit Schematic 4 _______________________________________________________________________________________
MAX1617A Temperature Sensor Evaluation Kit Evaluates: MAX1617 A
1.0"
Figure 2. MAX1617A EV Kit Component Placement Guide
1.0"
Figure 3. MAX1617A EV Kit PC Board Layout--Component Side _______________________________________________________________________________________ 5
MAX1617A Temperature Sensor Evaluation Kit Evaluates: MAX1617 A
1.0"
Figure 4. MAX1617A EV Kit PC Board Layout--Solder Side
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
6 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2002 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.

▲Up To Search▲

Price & Availability of MAX1617AEVKIT

	To Download MAX1617AEVKIT Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .